What're your thoughts on How to Install a Bathtub?
Installing a bathtub isn't specifically rocket science, yet it does call for strong plumbing, carpentry, and sometimes, tiling abilities. Replacing an old bathtub with a brand-new one is additionally a moderately challenging project. If the old bathtub is easily available, the task can relocate immediately; if you have to open a wall surface to remove the old bathtub and also position the new bath tub, the job is much harder. In either case, the job is within a home handyman's abilities, although you will need an assistant to move out the old bathtub as well as set in the brand-new one. Make certain you have certified yourself for the task and are comfortable trying it. Instead of working with a specialist to take control of a halfway-completed project, it is far better to consider utilizing one before you begin. Opportunities are you may require an expert plumber to make tube links.
This article will certainly aid you set up a brand-new bathtub in your shower room if you have actually already purchased a new bathtub and also don't need to alter the arrangement of your previous water system pipelines.
Your devices and also material checklist ought to comprise the following:
Removing Old Taps
If you need to replace old faucets with brand-new ones as a part of your installation, then the first thing you need to do is separate the water system. After doing so, turn on the taps to drain pipes any type of water staying in the system. The process of getting rid of the existing faucets can be rather problematic as a result of the restricted access that is usually the case.
Make use of a basin wrench (crowsfoot spanner) or a tap device to undo the nut that attaches the supply pipes to the faucets. Have a fabric all set for the staying water that will originate from the pipelines. When the supply pipelines have been removed, utilize the same device to loosen the nut that holds the faucets onto the bath/basin. You will require to quit the single faucets from transforming during this procedure. As soon as the taps have actually been gotten rid of, the holes in the bath/basin will need to be cleansed of any old securing substance.
Prior to moving on to fit the new faucets, contrast the pipe links on the old faucets to the new taps. If the old faucets are longer than the brand-new taps, then a shank adapter is needed for the brand-new faucets to fit.
Suitable New Taps
If the tails of the new taps are plastic, after that you will need a plastic port to avoid damages to the string. One end of the adapter fits on the plastic tail of the faucet and the other end offers a link to the existent supply pipelines.
If you need to fit a monobloc, then you will certainly call for lowering couplers, which connects the 10mm pipe of the monobloc to the common 15mm supply pipe.
Next, position the tap in the mounting opening in the bath/basin making sure that the washers are in place between the tap as well as the sink. Protect the faucet in position with the producer offered backnut. Once the tap is firmly in position, the supply pipelines can be linked to the tails of the taps. The taps can either be attached by utilizing corrugated copper piping or with typical tap connectors. The former kind must be linked to the tap ends initially, tightening up only by hand. The supply pipes can later on be attached to the various other end. Tighten both ends with a spanner after both ends have actually been linked.
Installing the Bathtub
Making use of both wooden boards under its feet, position the bath tub in the needed position. The wood boards are practical in uniformly spreading the weight of the bath tub over the location of the boards instead of concentrating all the weight onto 4 little points.
The following goal is to ensure that the bath tub is leveled all round. This can be accomplished by checking the level as well as adjusting the feet on the bath tub until the level checks out level.
To mount taps, fit all-time low of the outermost flexible faucet port to the appropriate supply pipe by making a compression sign up with; after that do the same for the various other tap.
Activate the water system and also inspect all joints and brand-new pipework for leaks and tighten them if needed. Fill the bath tub and additionally check the overflow electrical outlet and the typical electrical outlet for leaks.
Lastly, fix the bath paneling as explained in the manufacturer's instruction manual. Tiling and also sealing around the tub needs to wait until the tub has actually been used a minimum of when as this will settle it right into its last position.
Getting ready for the Installment
Firstly, the supporting structure provided with the bath should be fitted (if needed) according to the supplier's instructions. Next off, fit the faucets or mixer to the bathtub. When suitable the faucet block, it is essential to make certain that if the tap includes a plastic washing machine, it is fitted in between the bath and the taps. On a plastic bathroom, it is additionally sensible to fit a sustaining plate under the faucets unit to avoid pressure on the bath tub.
Fit the flexible tap adapters to the bottom of both taps using 2 nuts and olives (often provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and then pass the outlet with the hole in the bathroom. Make use of the nut supplied by the manufacturer to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the adaptable overflow pipe to the overflow outlet. After that, screw the pipe to the overflow face which must be fitted inside the bathroom. See to it you use all of the supplied washers.
Link the trap to the bottom of the waste outlet on the tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Attach the bottom of the overflow tube in a similar manner.The bath ought to now be ready to be fitted in its final setting.
Tiling Around the Tub
In the area where the bath satisfies the ceramic tile, it is needed to secure the accompanies a silicone rubber caulking. This is very important as the fitting can move enough to crack a rigid seal, causing the water to penetrate the wall between the bath and also the tiling, leading to complications with dampness and also feasible leakages to the ceiling listed below.
You can pick from a range of coloured sealers to blend in your fixtures and fittings. They are sold in tubes and cartridges, and also can securing spaces as much as a width of 3mm (1/8 inch). If you have a larger gap to load, you can load it with spins of drenched newspaper or soft rope. Remember to always load the bath tub with water prior to sealing, to allow for the movement experienced when the bathtub remains in use. The sealant can crack rather very early if you do not take into consideration this motion before securing.
Additionally, ceramic coving or quadrant floor tiles can be made use of to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also cut to dimension, are likewise easily readily available on the marketplace. It is recommended to fit the ceramic tiles using waterproof or water-proof sticky and cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
As a reader about Installing A Bathtub, I think sharing that excerpt was really useful. Loved our blog posting? Please share it. Help other people find it. I take joy in reading our article about Installing A Bathtub.
Further Details